1) La descarga del recurso depende de la página de origen
2) Para poder descargar el recurso, es necesario ser usuario registrado en Universia


Opción 1: Descargar recurso

Detalles del recurso

Descripción

If tribological contacts are not operating under full film lubrication, wear particles may be released which could significantly influence the lubrication performance and therefore the lifetime of machine elements. In this thesis, a model for the generation of wear particles in mixed lubrication will be described with emphasis on the running-in phase. The operating conditions and material were chosen to simulate the contact between a steel rolling element and cage (steel or brass) as can be found in rolling bearings. This thesis includes an experimental wear particle analysis and an efficient numerical algorithm (Boundary Element Methods, BEM) for the simulation of the generation of wear particles. First an efficient algorithm was developed for the calculation of friction in mixed lubrication based on a load sharing concept. The model was used to calculate the surface stresses that are needed for the wear model. It combined a finite difference based numerical elasto-hydrodynamic solver for the calculation of the hydrodynamic film and a BEM based solver for contact stress analysis. The friction model was successfully validated using measurements under various conditions. A (subsurface) stress-based BEM wear model was developed to calculate the size of wear particles. A critical Von Mises stress criterion was employed for the disruption of particles. The friction and wear models were combined to predict the generation of wear particles under mixed lubricated conditions. The model calculations show how friction reduces during running-in due to a smoothening of the surfaces. Steel and brass particles were collected and analyzed using Dynamic Light Scattering, Scanning Electron Microscopy and Atomic Force Microscopy and used for model validation. The model fitted the experimental data reasonably well for both, the steel and the brass materials. Finally, the model was extended to the growth and wear of tribo-films to also make it applicable if anti-wear additives are present. This effect was validated using experimental data from the literature. The thesis is divided into two parts. The first part (Part A) is a summary of the work. The second part (Part B) consists of the journal articles in which the details are described.

Pertenece a

University of Twente Publications  

Autor(es)

Akchurin, Aydar - 

Id.: 69523952

Versión: 1.0

Estado: Final

Tipo:  application/pdf - 

Tipo de recurso: Doctoral thesis  - 

Tipo de Interactividad: Expositivo

Nivel de Interactividad: muy bajo

Audiencia: Estudiante  -  Profesor  -  Autor  - 

Estructura: Atomic

Coste: no

Copyright: sí

Formatos:  application/pdf - 

Requerimientos técnicos:  Browser: Any - 

Relación: [References] http://doc.utwente.nl/102779/1/thesis_A_Akchurin.pdf

Fecha de contribución: 03-mar-2017

Contacto:

Localización:

Otros recursos que te pueden interesar

  1. Diversity patterns of Mediterranean grasslands: the relative influence of environmental and land use factors The objec!ves of this study are: 1) to iden!fy diversity pa#erns in Mediterranean therophy!c grassla...
  2. Prediction Of The Behaviors Of Hollow/Foam-Filled Axially Loaded Steel/Composite Hat Sections For Advanced Vehicle Crash Safety Design Hat sections, single and double, made of steel are frequently encountered in automotive body structu...
  3. Characterization of multidrug-resistant diabetic foot ulcer enterococci Introduction: Diabetes mellitus is a highly prevalent chronic progressive disease with complications...
  4. Within-lineage variability of ST131 Escherichia coli isolates from humans and companion animals in the south of Europe This is a pre-copyedited, author-produced version of an article accepted for publication in Journal ...
  5. Prevention of ventilator-associated pneumonia Artigo sob licença CC BY-NC-ND http://creativecommons.org/licenses/by-nc-nd/4.0/

Aviso de cookies: Usamos cookies propias y de terceros para mejorar nuestros servicios, para análisis estadístico y para mostrarle publicidad. Si continua navegando consideramos que acepta su uso en los términos establecidos en la Política de cookies.