1) La descarga del recurso depende de la página de origen
2) Para poder descargar el recurso, es necesario ser usuario registrado en Universia


Opción 1: Descargar recurso

Opción 2: Descargar recurso

Detalles del recurso

Descripción

Selective laser melting (SLM) of metallic powders is an additive manufacturing technique that is widely employed to produce 3D components, and is fast becoming an important method for manufacturing near-net shape and complex metallic parts. In this thesis, a comprehensive investigation on the effect of SLM on the mechanical and corrosion properties of the Al-12Si (AS), 316L stainless steel (SS), and 18(Ni)-300 grade managing steel (MS) is investigated, with particular emphasis on the developing (micro- as well as mesa-)structure -property correlations. Detailed microstructural characterization combined with quasi-static tensile, fracture toughness, fatigue crack growth, and unmatched fatigue tests were conducted. The effect of post-SLM heat treatment as well as the scanning strategy (linear vs. checker board hatch style) was examined and the results are compared with those of conventionally manufactured (CM) counterparts. The SLM alloys exhibit a mesostructured, in addition to the fine cellular structure along the boundaries. In a case of SLM-AS, the fine cellular structure imparts higher strength at the cost of ductility, while the mesostructured, which arises due to the laser track hatching, causes the crack path to be tortuous, and in turn leads to substantial increase in fracture toughness. This imparts significant anisotropy to the toughness while tensile properties are nearly-isotropic. The experimental results of SLM-SS also show that higher tensile strengths properties with a marked reduction ductility. In spite of these, the fracture toughness, which ranges between 63 and 87 MPa.m0.5, of the SLM-SS is good, which is a result of the mesostructured induced crack tortuousity.Both tensile and toughness properties of SLM-SS were found to be anisotropic in nature. Upon aging SLM-MS, nanoscale precipitation of intermetallic compounds occurs within the cells that, in turn, lead in marked improvements in tensile strengths properties, but substantial reductions in ductility and fracture toughness. Overall, the mechanical performance, except ductility, of the SLM-MS after aging is found to be similar to that of CM-MS. Importantly, the lack of ductility does not lead to a reduction in toughness. Although the SLM-MS alloy possesses a mesostructured, no significant anisotropy in the mechanical behaviour is observed. The unnoticed studies on SLM-AS, -SS, and -MS reveal that the tensile residual stresses, gas-pores, and unmelted powder particles, can degrade the unmatched highest fatigue properties considerably and hence need be eliminated for high fatigue strength. Room temperature, electrochemical corrosion resistances (CRs) of SLM-AS, -SS and -MS in 0.1M NaCl solution were also evaluated and compared with those CM counterparts. While SLM improves CRs of AS and SS, it degrades that of MS. The results are discussed in terms of microstructural refinement and porosity that are common in SLM alloys.

Pertenece a

ETD at Indian Institute of Science  

Autor(es)

Suryawanshi, Jyoti Balaji - 

Id.: 71337562

Idioma: inglés (Estados Unidos)  - 

Versión: 1.0

Estado: Final

Palabras claveLaser Melted Alloys - 

Tipo de recurso: Thesis  - 

Tipo de Interactividad: Expositivo

Nivel de Interactividad: muy bajo

Audiencia: Estudiante  -  Profesor  -  Autor  - 

Estructura: Atomic

Coste: no

Copyright: sí

Requerimientos técnicos:  Browser: Any - 

Relación: [References] G28322

Fecha de contribución: 24-may-2018

Contacto:

Localización:

Otros recursos de la mismacolección

  1. Microstructural Studies on High Cr-Mo Secondary Hardening Ultra-High Strength Steels Secondary hardening ultra-high strength (SHUHS) steels possess a unique combination of strength, fr...
  2. Bioremediation of Chromium : Mechanisms and Biosensing Applications Water pollution, especially caused due to the indiscriminate release of heavy metals as a result of ...
  3. Design and Fabrication of Conjugated Molecule Based Resistive Sensor for Environmental Monitoring Detecting Targeted Analytes Volatile organic compounds (VOCs) in air and heavy metal ions, anions, microorganism in water are en...
  4. Effect of Humidity and Temperature on Wear of TiN and TiAIN Coatings When loss of material due to sliding of two solids is promoted/prevented, in the presence of chemica...
  5. Whisker Growth from Electrodeposited Sn Coatings - Developing Materials Science and Mechanics Based Insights Pure Sn and Sn-alloys are widely used in electrical and microelectronic devices as protective layer ...

Aviso de cookies: Usamos cookies propias y de terceros para mejorar nuestros servicios, para análisis estadístico y para mostrarle publicidad. Si continua navegando consideramos que acepta su uso en los términos establecidos en la Política de cookies.